model-621

Model 621

This advanced service door is best suited to situations and applications with weather extremes. For example, agricultural facilities in the Midwest would benefit from the door’s rugged construction and weather sealed jambs.

Slat Type

F-265 & FE-265 SLAT

Fenestration

SLAT FENESTRATION - 3in X 0.625

SLAT FENESTRATION - 10in X 1in

Accessories

Flat profile type F-265 for doors up to 20’ wide also available in: 20, 18 gauge galvanized steel; 22, 20 gauge stainless steel; 16 gauge (.050”) aluminum
Bottom bar also available in: galvanized steel, stainless steel and aluminum
Wear strips are on available option, please note however that the 20 PSF wind load rating is no longer available when wear strips are selected
Guide options include: galvanized steel and powdercoated steel
Hood also available in: powdercoat, stainless steel and aluminum.
Brackets also available in: powdercoat and galvanized steel
Direct drive motors available in 1 HP, 2 HP, 3 HP, and 220 VAC 1-phase and 208/230/460/575 VAC 3-phase
Dual photoelectric sensors available for safety
Optional push buttons, loop detectors, radio control, motion detectors, or any combination thereof available for door operation/control
PowderGuard® Max powder coat finish options are available in approximately 200 colors as well as custom matching to specification. On the RapidSlat® models, PowderGuard® Max is required on curtain to maintain warranty on finish
PowderGuard® Textured powdercoat: Industrial textured powdercoat provides a thicker, more scratch resistant coat for added product protection available on brackets, guides and bottom bar
Vision lites on 18 ga. steel slats uniformly spaced of 3" x 5/8" (76 mm x 16 mm) or 10” x 1” (254 mm x 25.4 mm)

Colours

White

Gray

Tan

Actual door color may vary from the digital representation shown here.

Color samples are available by request.

Powder Coat Color Options

PowderGuard® Max powder coat options are available in approximately 200 colors as well as custom matching to specification. On the RapidSlat® PowderGuard® Max is required to maintain warranty on finish.

PowderGuard® Max formula is four times harder than our PowderGuard® Premium, providing ehanced strength and durability to the finish and performs well in high cycle applications. Finish also provides easy to clean surface. Available in white, tan, and gray or select a color from approximately 200 RAL powder coat colors.

Features

Standard max width:

up to 20' (6096 mm) depending on gauge and slat type

Standard max height:

up to 20' (6096 mm) depending on gauge and slat type

Mounting:

Interior or exterior face of wall

Hood:

24 gauge galvanized steel primed, black painted; interior hood baffle included

Brackets:

Min. ¼” hot rolled primed, PowderGuard® Premium powder coated black steel

Guides:

Three structural steel angles PowderGuard® Premium powder coated black

Actuator:

Single open/close/stop push button station incorporated into control panel

Wind load:

20 psf when optional wear strips are not specified

Curtain finish:

Gray, tan or white PowderGuard® Max powder coat with hardening additive

Control panel:

Variable frequency drive controller with self-diagnostics (time delay self-close timer and non-resettable cycle counter included); LCD readout, enclosure NEMA 4X rated

Curtain:

Interlocking roll-formed slats, end locks attached to prevent lateral movement. Flat Profile type F-265 for doors up to 20' wide; 22 gauge galvanized steel

Bottom bar:

Two PowderGuard® Premium powder coated black angles (min. thickness 3/16”) with 2-wire, self-monitoring, fail safe, electric sensing edge

Door roll:

Direct driven, springless roll with integrated shafts; self-aligning grease-able sealed bearings; door does not require counterbalance device

Operation:

Direct drive, integrated gear motor/brake assembly (up to 24” per sec up speed / 12” per sec down speed); drive assembly and limit sensors are factory pre-assembled; manual hand chain for power outage